EasyTint™ Tinted Concrete Sealer
EasyTint™ Tinted Concrete Sealer
- Color and seal your concrete in one step — solvent-based durability — Professional-grade solvent-based sealer with pigment built in. Satin finish engineered for exterior high-traffic applications.
- 30 professional colors — Full range from warm earth tones to deep neutrals and accent colors. Test 3 colors before committing with the EasyTint™ Trial System.
-
Coverage: 200 sq ft per gallon (two coats recommended) — Available in 1-gallon and 5-gallon sizes. Select your size from the dropdown above.
How much do I need to stain my concrete?
- It will depend on the square footage of your application.
- The coverage rate is 200 square feet per gallon (2 coats) depending on concrete porosity. Two or more coats are required.
Concrete Stain Calculator
Amounts of coats:
Amount of EasyTint™ to use:
Your Recipe:
| Size | Qty |
|---|
Product Details
Product Details
Color and Seal Your Concrete in One Step — Maximum Durability
EasyTint™ is a professional-grade, solvent-based tinted concrete sealer that adds permanent color to concrete and seals the surface at the same time. One product. One application. Your concrete is colored and protected in a single step — with the traditional solvent-based acrylic durability that contractors have relied on for decades for the toughest exterior applications.
EasyTint™ is the choice for concrete driveways, commercial walkways, high-traffic patios, stamped concrete, and any exterior surface where the finish needs to hold up to years of weather, UV exposure, vehicle traffic, freeze/thaw cycles, and daily wear. The solvent-based chemistry delivers a harder, more durable cured film than water-based alternatives, which translates into longer-lasting color and better long-term performance under hard conditions.
EasyTint™ cures to a satin finish that preserves the natural look and texture of concrete while adding the rich, durable color your project needs. For contractors, the color-and-seal-in-one format cuts project time roughly in half — one product, one visit, one application instead of the traditional multi-step process.
What EasyTint™ Does and How It Works
EasyTint™ is a solvent-based acrylic sealer with pigment dispersed throughout the product. When you apply it to clean, prepped concrete, the sealer forms a durable protective film on the surface while the pigment delivers rich, even color. As the solvent evaporates, the acrylic cures into a permanent finish that protects the concrete from water penetration, UV exposure, stains, and surface wear — and the pigment is locked into that seal, delivering consistent color across the entire surface.
The solvent-based chemistry gives EasyTint™ deeper pigment penetration into the concrete pore structure and a harder, more durable cured film than water-based colored sealers. For high-traffic exterior applications — driveways that handle daily vehicle traffic, commercial walkways that see thousands of footsteps per week, patios in harsh climates — this durability advantage is the reason to choose EasyTint™.
The recommended application is two coats, which delivers full color saturation and maximum surface protection. EasyTint™ covers approximately 200 square feet per gallon with the recommended two-coat application.
What EasyTint™ Tinted Concrete Sealer Is Used For
Residential concrete driveways — The classic use case for EasyTint™. Colors and seals a driveway in one step with the solvent-based durability that handles years of vehicle traffic, weather, and UV exposure. For heavily-used driveways, apply a clear solvent-based sealer topcoat for additional protection.
Stamped concrete — EasyTint™ colors and seals stamped concrete surfaces in one application, delivering rich color in the texture and recesses of the stamp pattern while protecting the entire surface. Popular on stamped patios, courtyards, walkways, and pool surrounds.
High-traffic commercial walkways and entryways — Retail storefronts, restaurant entrances, commercial building walkways, and hotel exteriors where durability and professional appearance both matter.
Concrete patios — Backyard patios, outdoor entertaining areas, and courtyards. EasyTint™ handles weather, UV, and foot traffic on exterior patios.
Concrete walkways — Front walks, garden paths, and commercial paths.
Concrete pool decks — Pool surrounds where you want color and protection. For pool decks, a clear topcoat with slip-resistant additive is required (see topcoat guidance below).
Exterior concrete stairs and ramps — Where slip resistance is needed, use EasyTint™ as the color layer and a clear solvent-based sealer with OxiGrip™ as the topcoat.
Cold climate and freeze/thaw zone applications — The solvent-based chemistry handles freeze/thaw cycles better than water-based alternatives. For exterior concrete in northern climates, this matters.
Faded or weathered concrete restoration — Old exterior concrete brought back to life with color and a fresh seal in one step.
See EasyTint™ on real customer projects — Browse the Direct Colors customer photo gallery to see EasyTint™ applied to driveways, patios, stamped concrete, and commercial surfaces across the country.
Specifications
Specifications
| Finish | Satin (low-sheen, natural look) |
|---|---|
| Acrylic Solids | 25% |
| Application Tools | Pump sprayer or 3/8" nap roller with solvent-resistant core |
| Location | Interior (with ventilation) or exterior |
| Dry Time | Touch: 4–6 hrs | Foot traffic: 16–24 hrs | Vehicle traffic: 24–48 hrs |
| Recoat Time | 6–12 hours depending on conditions |
| Cleanup | Xylene or similar solvent |
| Coverage | ~200 sq. ft. per gallon (two thin coats recommended) |
| Application Temp | 40°F–95°F (4°C–35°C) |
| Recommended Topcoat | EasySeal™ Satin solvent-based acrylic sealer |
| VOC | <83% |
| Flash Point | 92.9°F (38.87°C) |
| Important Note | Requires proper ventilation due to strong fumes |
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Frequently Asked Questions
How does EasyTint™ work?
How does EasyTint™ work?
EasyTint™ is a clear, solvent based concrete sealer with pigment added to it - along with a few other ingredients. It’s a stain and sealer in one, allowing you to stain and subtly color your concrete simultaneously. When you apply the sealer, the pigments suspend in the sealer, providing beautiful, tinted color. AcquaTint™ produces a semi-translucent color with a much more natural look and durable finish than concrete paint.
Where can I apply EasyTint™ colored sealer?
Where can I apply EasyTint™ colored sealer?
Effective on most concrete surfaces, EasyTint™ is a UV stable colorant that can be applied on both indoor and outdoor projects. For best results, we recommend that tinted sealer is applied in areas intended primarily for foot traffic. You definitely want to consider ventilation. Since EasyTint™ is a solvent-based product, it will off-gas a strong chemical odor for 3-5 days depending on ventilation. If this is an issue, you should consider AcquaTint™, which is a low VOC, water-based version of EasyTint™.
I’ve just applied EasyTint™ to my concrete and after it dried, it barely has color. What happened?
I’ve just applied EasyTint™ to my concrete and after it dried, it barely has color. What happened?
Fortunately, this isn’t something we hear very often. The good news is that concrete pigments don’t disappear! Assuming your concrete surface is in relatively decent condition and isn’t extremely deteriorated, the tinted sealer you applied is still in place. Sometimes on severely aged or deteriorated concrete surfaces, the extreme porosity “drinks” the sealer in. As the pores absorb the sealer, the pigments are taken with it - diminishing the color result. It may take additional coats of concrete sealer to develop a more vibrant color. In this case, we prefer to review your project with you before you apply more product.
How do I know if my concrete is properly prepared for EasyTint™ tinted sealer?
How do I know if my concrete is properly prepared for EasyTint™ tinted sealer?
Before applying EasyTint™, you should lightly etch the surface of the concrete with CitrusEtch™ concrete etcher (or sand) if the surface is very smooth. The sanded or etched surface will promote better adhesion of the sealer as it bonds to your concrete.
How much surface preparation is required to use EasyTint™?
How much surface preparation is required to use EasyTint™?
Surface preparation is often the most critical factor in any successful decorative concrete project. In order to achieve the best results, the concrete surface should be free of cure and seal, sealer, paint, dirt, grime, and grease. Remember to practice proper preparation - if the sealer can’t bond well, it can lead to the finish peeling up along with the color. Trust us, it’s totally worth it to put in the extra time to set yourself up for a successful and long-lasting project!
I purchased the amount of product your concrete stain calculator recommended based on my square footage, and still needed more. What happened?
I purchased the amount of product your concrete stain calculator recommended based on my square footage, and still needed more. What happened?
Depending on your concrete surface and chosen application methods, coverage rates can vary. We follow industry standards of approximately 200 square feet per gallon, which commonly applies to lower viscosity products like colorants and concrete sealers. First, it’s always good to double-check your calculation of square footage. From there, a few variables come into play. How porous, weathered, or worn is your concrete? How heavily are you applying the product? On smoother, less porous concrete, you may find you’re getting a bit more coverage than anticipated. For stamped, textured, or more weathered, porous concrete, you may get a bit less coverage. These variables aren’t calculation errors, but more of a common indefinite. When in doubt, follow the general construction rule of rounding up for your supply needs.
I applied EasyTint™ concrete sealer and it has started to flake or peel off, what did I do wrong?
I applied EasyTint™ concrete sealer and it has started to flake or peel off, what did I do wrong?
Most often, any sealer releasing from concrete is due to a short list of reasons. The concrete wasn’t properly cleaned and dirt, residues, or other contaminants prevented proper adhesion. The concrete was too smooth (slick), and the tight surface did not allow proper penetration or adhesion to the concrete. When sealer is over-applied, the heavy amount of caked-on acrylic becomes soft or spongy, leading to a weakened finish that will deteriorate quickly. This can also lead to trapped moisture, particularly on exterior concrete. In most cases, two thin coats of AcquaTint™ will provide you with a long-lasting decorative finish.
I applied EasyTint™ on my patio and there are areas that look hazy or whitish in color, what is going on?
I applied EasyTint™ on my patio and there are areas that look hazy or whitish in color, what is going on?
This somewhat common problem can be avoided with a few simple considerations. First, what’s happening? The culprit is usually moisture. Most acrylic sealers are designed to pass around 3% or 4% of moisture when applied correctly in two thin coats. When the moisture rate exceeds this, the moisture cannot escape, becomes trapped, and creates a white or cloudy effect. A few preventative measures: Make sure that the concrete you’re sealing isn’t located in a space that holds water after rain for an extended period. Sealers left submerged underwater will soon begin to lose performance. If your concrete is in low-lying areas at risk of being submerged, consider installing drains, rock beds over sand for quick absorption of water, or a trench next to the concrete so water can be redirected away from your decorative finish.
Why choose gloss finish?
Why choose gloss finish?
The high-gloss formula is designed for homeowners and contractors who want maximum visual impact. Its 30% acrylic solids content creates a thicker, more reflective film that darkens surfaces to a rich wet-look appearance. This makes it especially effective at reviving aged or faded concrete, amplifying the depth of previously stained surfaces, and creating a polished, showroom-quality look on patios and entryways. The higher solids concentration also contributes to enhanced surface smoothing, filling in minor imperfections while delivering a uniform, mirror-like sheen.
How to Apply EasyTint™
Explore our full range of EasyTint™ translucent concrete colors and find the perfect tone for your project.
- Preparation
- Application
- Drying Times & Protection
- Maintenance & Safety
Product Videos
EasyTint™ Satin
Explore the complete EasyTint™ Satin palette and discover the perfect shade for your concrete project.
- Semi-transparent colors that enrich natural concrete texture
- Low-sheen satin finish ideal for patios, walkways, and pool surrounds
- Adds understated color while protecting outdoor concrete surfaces
- Designed for entryways, textured, stamped, and decorative concrete
⚠️ Important: When You Need a Clear Topcoat Over EasyTint™
EasyTint™ is a complete color-and-seal product for most applications. For many residential patios, walkways, and low-traffic exterior surfaces, two coats of EasyTint™ is the finished job. However, a clear topcoat is either recommended or required in certain situations:
| Application | Topcoat Needed? | What to Use |
|---|---|---|
| Interior floors (general) | Recommended | ProWax Polish™ — acts as a sacrificial layer that protects the color finish from daily foot traffic. Easy to reapply as it wears. |
| Exterior low-traffic (patios, walkways) | Not required | EasyTint™ alone is sufficient |
| Exterior high-traffic (driveways, commercial) | Recommended | A clear solvent-based concrete sealer for added durability |
| Slip resistance required (pool decks, stairs, ramps) | Required | Clear solvent-based concrete sealer + OxiGrip™ slip-resistant additive |
Technical Data Sheets
Before
After