FREE Shipping Orders Over $199 (exclusions apply)
Product Search

My Cart: 0 item(s)


cccc '38086'

$0.00

Financing available with . Learn more
  • Color or restore faded concrete
  • Ideal for lightly textured, broomed and stamped concrete
  • Can be applied to previously colored concrete
  • NOTE: Antiquing stain must be sealed after application

    How much do I need to stain my concrete?

    It will depend on the square footage of your application.

    The coverage rate is 200 square feet per gallon (2 coats) depending on concrete porosity. Two or more coats are required.

    Your answer will appear here.

    Choose Quantity:


    Product Tabs

    Product Details

    Easily add or restore color to previously stained concrete driveway, pathway, patio, or any stamped concrete where color has faded. Our premium, spray-on formula applies directly on top of concrete in combination with our top-of-the line sealers provide you with a fade resistant, low maintenance, and easy to clean outdoor living space for many years to come. 
     
    Quick Facts
    • Application Tool: Pump Sprayer
    • Dry Time: 6 - 8 hours before applying EasySeal™ (sealer application is a required step)
    • Cleanup: Mineral Spirits
    • Coverage: Approximately 200 sq. ft. per gallon depending on porosity
    • Exterior Sealer: EasySeal™
    • Recommended Uses: Concrete patios, driveways, pool decks, walkways or any textured, brushed or stamped concrete surface.


    Note: Since this is a made to-order-product, we cannot offer refunds, exchanges, or returns.
    Due to DOT-ORM-D regulations, this product cannot be expedited and can only be shipped by ground.



    Where To Apply Antiquing Stain

    New or existing exterior stamped concrete surfaces such as: Patios, Driveways, Pool Decks, and Walkways. 


    When Not To Apply Antiquing Stain

    DO NOT apply Antiquing Stain In poorly ventilated areas and/or very smooth concrete surfaces.


    Restore Faded Stamped Concrete Color



    Stain Over Repaired Cracked Stamped Concrete




    Disclaimer: Direct Colors does not warrant or guarantee results (outcomes). Concrete variations or improper application may cause unintended results. Test product on an inconspicuous or small area and allow to fully cure to ensure compatibility and desired result.

    FAQ

    Click/Tap each question to hide/show the answers.

    How does Antiquing™ Stain work?

    Concrete Antiquing™ Stain is a solution formulated using pigments. Once this concrete stain is applied to a concrete surface, the liquid remains wet for an extended period, allowing the pigments to travel and nest in the lower depressions of the surface. When they've completed dried, the pigments deposit lightly on the higher spaces and heavily in the lower depressions - resulting in that beautiful "antique" finish (hence the name!). Since Antiquing™ Stain is a pigment-based colorant, the pigments need to be held in place with a concrete sealer.

    Where can I apply concrete antiquing stain?

    Typically intended for outdoor surfaces, Antiquing™ Stain is specifically-engineered for stamped concrete that remains in good condition. It can also be applied to hand-troweled, hand-textured, or brushed concrete. However, when the concrete doesn't have depressions, such as a slate finish or other design, the color typically produces a more uniform result (depending on the application method). If your concrete is extremely porous, weathered, or degraded, consider using our Portico™ Paver Stain for better color results. If you're unsure, check out an Antiquing™ Stain Trial Kit or Portico™ Paver Stain Trial Kit to confirm results for you before you start on a full project.

    After antiquing concrete and letting it dry, it barely looks like I have any color. What happened?

    The good news is that concrete pigments don't disappear! Assuming your concrete surface is in good condition and not extremely porous, weathered, or otherwise degraded, the pigments you sprayed down are still in place. Once Antiquing™ Stain is sprayed on the surface and dries for several hours, the dried pigment only appears faded. When you apply the recommended two thin coats of concrete sealer, the color will "pop" to life, transforming your space! Be mindful of a decision you'll need to make between solvent-based or water-based sealers. While both are great options, the difference is that solvent-based sealers will "pop" color much more intensely than water-based sealers. Water-based sealers will tend to soften in color as they cure.

    Why didn’t Antiquing™ Stain work on my concrete?

    It would be unusual if the antiquing stain didn’t color your concrete surface successfully. Remember, this product is made of pigment, and pigments don't disappear! If Antiquing™ Stain didn't add any color to your concrete, it could potentially be one of two issues: 
    1. The pigments became trapped or blocked in the sprayer. This can make it seem as if you sprayed liquid with no color. Make sure that you have removed all of the filters on the stain sprayer and that the O-rings are seated correctly in the sprayer head. 
    2. The concrete that you're applying Antiquing™ Stain to is far too porous, weathered, or degraded. When concrete is extremely porous, the pigments will fall deeper into the concrete surface - causing the color to diminish. This is not a sign of a faulty product, but unfortunately, you may have selected the wrong product for your particular project.

    How much surface preparation is required to antique concrete?

    Surface preparation is often the most critical factor in any successful decorative concrete project. In order to achieve the best results, the concrete surface should be free of cure and seal, sealer, paint, dirt, grime, and grease. If the concrete was previously stained and the original sealer has worn away, go ahead and apply Antiquing™ Stain over that previous stain. What you would particularly want to avoid is applying the Antiquing™ Stain over a previously sealed surface. This could cause the still intact sealer to repel the new stain you’ve applied. Scrub the surface using ProClean Degreaser, rinse thoroughly, and allow to dry before applying Antiquing™ Stain.

    I purchased the amount of product your concrete stain calculator recommended based on my square footage, and still needed more. What happened?

    Depending on your concrete surface and chosen application methods, coverage rates can vary. We follow industry standards of approximately 200 square feet per gallon, which commonly applies to lower viscosity products like colorants and concrete sealers. First, it's always good to double-check your calculation of square footage. From there, a few variables come into play. How porous, weathered, or worn is your concrete? How heavily are you applying the product? On smoother, less porous concrete, you may find you're getting a bit more coverage than anticipated. For stamped, textured, or more weathered, porous concrete, you may get a bit less coverage. These variables aren't calculation errors, but more of a common indefinite. When in doubt, follow the general construction rule of rounding up for your supply needs.

    I ordered a trial kit and we found the color we are going with. Can I stain yet this fall and seal in the spring? No way will we meet the temperature requirements for sealing this year.

    Antiquing™ Stain should be sealed 8 -10 hours after application to prevent the pigments from being displaced by wind or weather.

    Is concrete antiquing stain permanent?

    No, Antiquing™ Stain is a topical colorant with UV-stable and fade-resistant pigments. As the product is applied, the pigments will nest into the pores of the concrete, the solvent-based liquid will off-gas and dry, and then a sealer will need to be applied to keep the colorant on the surface. You must maintain the sealer to protect your color.

    How long does the Antiquing™ Stain need to dry before applying sealer?

    For exterior concrete, allow at least 8 hours for Antiquing™ Stain to dry and off-gas before applying acrylic solvent-based sealer.

    What should I use for cleanup of Antiquing™ Stain?

    Odorless mineral spirits should be used for the cleanup of Antiquing™ Stain.

    Can I use antiquing concrete stain in my garage?

    We would recommend a different product for staining your garage floor, such as our Vibrance Dye. For a more permanent color change, consider EverStain Acid Stain.

    How-To Guide

    Printable Antiquing™ How-To Guide

    Step 1: Preparation

    • Cover areas at risk of over-spray with plastic drop cloth.
    • Newly poured concrete must cure for 30 days before application.
    • For existing concrete:
      • Remove paint or previously applied sealer using Soy Gel Stripper.
      • Remove carpet glue or other adhesives using Bean-E-Doo® Mastic Remover.
      • Remove any oils, dirt, debris, Soy Gel Stripper, or Bean-E-Doo® Mastic Remover using scrub brush and ProClean Degreaser™.
    • Verify absorption by pouring a cup of water in various areas. If not absorbed within five minutes, etch the surface with CitrusEtch™, then neutralize surface with ProClean Neutralizer™ and rinse thoroughly.
    • Allow the concrete to thoroughly dry before application.

    Step 2: Application

    Coverage rate is approximately 200 square feet per gallon. Coverage rates may vary based on concrete texture, surface porosity, and application method.

    NOTE: Only apply Antiquing™ Stamped Concrete Stain when surface temperature is between 40 °F (4 °C) and 95 °F (35 °C).

    CAUTION: Antiquing™ is flammable, harmful if swallowed, or inhaled. Keep away from heat, sparks, and flame. Store and use with adequate ventilation, allowing airflow to disperse vapors. Before applying Antiquing™, open windows and doors and extinguish all open flames such as gas appliance pilot lights, candles, etc. Do not smoke, use a lighter or matches, or anything that could cause a potential spark.

    Spraying:

    • Remove all filters from pump-up sprayer
    • Shake Antiquing™ well before pouring into sprayer.
    • Spray Antiquing™ on surface in slightly circular motions with irregular overlaps.
      • Shake sprayer tank from side to side often to prevent color from settling.
    • Allow to thoroughly dry for a minimum of eight hours before applying sealer.

    Step 3: Seal & Protect Finish

    • Apply two thin coats of sealer (AcquaSeal™ Water-Based Acrylic Sealer or EasySeal™ Solvent-Based Acrylic Sealer).
    • For additional application instructions, see AcquaSeal™ and EasySeal™ for How-To Guides.

    Pro Tips:

    • Begin spraying at a far corner to maintain a clear path to exit.
    • To avoid droplets dripping onto surface: before releasing sprayer trigger, immediately place tip in a bucket.

    Cleanup:

    • Clean tools and supplies with odorless mineral spirits

    Maintenance:

    • Protect finish every two years or as needed with either AcquaSeal™ Water-Based Acrylic Sealer or EasySeal™ Solvent- Based Acrylic Sealer.
    • For additional application instructions, see AcquaSeal™ and EasySeal™ for How-To Guides.

    Tools & Supplies:

    • Pump-up sprayer
    • Plastic drop cloth
    • Scrub brush
    • Spiked shoes (if using CitrusEtch™)

    Disclaimer: Direct Colors does not warranty or guarantee results (outcomes). Concrete variations or improper application may cause unintended results. Test product on an inconspicuous or small area and allow to fully cure to ensure compatibility and desired result.

    How-To Videos

    Data Sheets

    Color Chart

    Antiquing Stain - Color Chart

    Customer Reviews:

    Loading Reviews...

    x

    Shipping Estimate

    Estimate Shipping
    • Use 2 letter code