FREE Shipping Orders Over $199 (exclusions apply)
Product Search

My Cart: 0 item(s)


Financing available with . Learn more
  • Enhances concrete grip, reducing slip risks
  • Ideal for pool decks, patios, and walkways
  • Compatible with EasySeal™ and AcquaSeal™ for optimal safety

Choose Quantity:

Product Tabs

Product Details

OxiGrip™ Slip-Resistant Additive: Ensure foot safety with our advanced formula designed for seamless integration with EasySeal™ and AcquaSeal™. Enhance the traction and durability of your outdoor surfaces such as pool decks, steps, patios, and garages.

Special Note: Direct mixing with tinted sealers (AcquaTint™ or EasyTint™) is not recommended. For a slip-resistant finish post-tinting, use a top coat of the corresponding sealer with OxiGrip™.

Quick Facts

Application Tools: Achieve the best results with a pump sprayer (filter removed), ⅜” nap roller, or seed spreader.
Location: Suitable for exterior surfaces requiring slip resistance.
Dry Time: Consult the Technical Data Sheets (TDS) for AcquaSeal™ TDS and EasySeal™ TDS for specifics.
Cleanup: Use water.
Coverage: 3-Ounce Packet: Mix with 1 gallon (3.79 liters) of sealer for approximately 200 sq. ft. of coverage.
10-Ounce Packet: Mix with 5 gallons (18.93 liters) of sealer for approximately 1000 sq. ft. of coverage.
Recommended Sealers: Compatible with AcquaSeal™ Water-based Acrylic Sealer or EasySeal™ Solvent-based Acrylic Sealer.
Application Temperature: Consult the Technical Data Sheets (TDS) for AcquaSeal™ TDS and EasySeal™ TDS for specifics.
Recommended Uses: Perfect for enhancing safety on stamped concrete driveways, patios, pool decks, walkways, and more.
Important Note: Always ensure good ventilation when applying solvent-based sealers due to potent fumes.

How-To Guide

Product Coverage

OxiGrip™ must be mixed with sealer before application.

3-Ounce Packet Mix with 1 gallon (3.79 liters) of sealer. Yields coverage for about 200 sq. ft.
10-Ounce Packet Mix with 5 gallons (18.93 liters) of sealer. Yields coverage for about 1000 sq. ft.


First, ensure the initial coat of sealer has fully dried. OxiGrip™ Slip-Resistant Additive is then added to the final coat of sealer for application.

Sprayer Application

  • Setup: Remove filters from an all-plastic pump-up sprayer. Remove filters from an all-plastic pump-up sprayer. Fill with the OxiGrip™ and sealer mix at the specified dilution rate. Hand showing filter removal from a pump-up sprayer
  • Application: Evenly apply the sealer mix across the surface to prevent pooling. This method is ideal for large, open areas.

Roller Application

  • Preparation: Mix OxiGrip™ with the sealer intended for the final coat. Ensure thorough mixing before each use.
  • Application: Apply the mixture evenly using a 3/8” nap roller, aiming for a thin, uniform coat. Roller application is suited for precise control over coverage.

Broadcast Application

  • Base Layer: Apply a thin layer of sealer according to the EasySeal™ or AcquaSeal™ Technical Data Sheet.
  • Broadcasting OxiGrip™: While the base layer is still wet, evenly spread OxiGrip™ over it. Use gloves for hand application or a seed spreader for uniform distribution. Move backwards to avoid stepping on the wet sealer.
  • Final Coat: After 4-6 hours, once the base layer has dried, apply another thin coat of sealer and repeat the broadcasting process if needed. This method is best for textured surfaces where even distribution of the additive is crucial.

Remember, OxiGrip™ should only be added to the sealer used for the final coat to ensure optimal slip resistance and durability of the finish.


  • Slip Resistance vs. Non-Skid: OxiGrip™ enhances slip resistance for safer foot traction but does not create a non-skid surface. Slip resistance helps reduce the likelihood of slipping on wet surfaces, while non-skid surfaces are designed to prevent slipping under almost all conditions.
  • Compatibility: OxiGrip™ is not compatible with EasyTint™ or AcquaTint™ tinted sealers. For tinted surfaces, consider applying a clear top coat of sealer with OxiGrip™ for slip resistance.
  • Surface and Environmental Conditions: The effectiveness of OxiGrip™ may vary based on surface type and environmental conditions. It is not recommended for use on [specific surfaces, if any], and optimal application conditions include [mention any specific temperature or humidity requirements].


For cleaning tools and equipment use ProClean Neutralizer™ solution.


Dispose of unused product according to local environmental or hazardous waste regulations.

Shelf Life and Storage

Store OxiGrip™ in a cool, dry place. If unopened and stored properly, its shelf life is approximately 3 years. Avoid extreme conditions.

Complementary Products

ProClean Neutralizer™ Concrete cleaner & neutralizer
Spiked Shoes Prevents shoe prints in wet product
AcquaSeal™ Water-based acrylic sealer for exterior surfaces
EasySeal™ Solvent-based acrylic sealer for enhanced durability

Safety & Precautions

CAUTION: Avoid contact with eyes and skin. Do not breathe dust. Do not take internally. In case of eye contact, flush thoroughly with water. In case of skin contact, flush thoroughly with water. If breathed in, move person into fresh air. If swallowed, do not induce vomiting. Call physician immediately. KEEP OUT OF REACH OF CHILDREN. WARNING: This product can expose you to Silica, crystalline, which is known to the State of California to cause cancer. For more information go to


OxiGrip™ is guaranteed for uniform quality within manufacturing tolerances. No warranty is provided for its application effects. Liability for defects is limited to refunding the purchase price. Users bear all other risks and liabilities. For inquiries, contact Direct Colors customer service.

PDF Downloads

Customer Reviews:

Loading Reviews...


Shipping Estimate

Estimate Shipping
  • Use 2 letter code